
EV Charger Installation in Janesville, WI
Updated
Get a free quote
A licensed electrician replies with a price. Nothing is booked until you say yes.
Rather talk? Call (608) 554-4028 or text us.
Short answer
Ready for a price on ev charger installation?
Call, text, or send the form. You get a written price back before anything is scheduled.
What the job is
A Level 2 charger runs on 240 volts, the same as a dryer or a range, on a dedicated circuit from the panel. The electrician sizes the breaker and wire to the charger, runs the circuit to the garage wall or an outdoor post, and either hard-wires the charger or installs a 240-volt receptacle for a plug-in unit. The long part of most jobs is the distance from the panel to where the car parks.
What it costs in Wisconsin
ElectrifyCost's Wisconsin range is $832 to $2,912 (ElectrifyCost). PermitDeck's Milwaukee table puts a Level 2 install at $1,287 to $2,178 (PermitDeck), and a Milwaukee-area contractor lists $800 to $2,500 including permit coordination (its 2026 price guide). Whether the charger hardware is in the number varies by quote, so ask. A panel that has to grow first is a separate line: about $1,500 to $4,500 for 200 amps. All of it is on the cost page.
The permit
Janesville requires a permit for any new wiring or any change to existing wiring (City of Janesville), and state code says no wiring project that adds a branch circuit may start without one (SPS 316.012). An EV circuit is a new branch circuit. A homeowner who owns and lives in the house may pull a branch-circuit permit in Janesville, but if the job touches the service, a licensed Master Electrician pulls it. Fees are in Janesville electrical permits.
Will the panel carry it?
A charger is a large, long-running load, often overnight alongside the furnace, water heater and dryer. On a 100-amp service in an older house that is where the electrician's load calculation earns its fee. The answer is one of three: the circuit fits as is, a load-management device lets it share capacity, or the service gets upgraded. Homes built from 1965 to the mid 1970s may also have aluminum branch wiring worth checking before adding load (aluminum wiring).
The code it is inspected to
Wisconsin adopted the 2023 National Electrical Code effective September 1, 2026 (CR 26-016), so new EV circuits are inspected to that edition, not the 2017 one most online install guides were written for.
Sources: ElectrifyCost, EV charger install cost in Wisconsin; PermitDeck, electrical costs in Milwaukee, WI (modeled from RSMeans, BLS and NECA data); a Milwaukee-area electrical contractor's published 2026 price guide; City of Janesville Building Division, building permits; Wis. Admin. Code SPS 316.012, electrical permits; Wisconsin Clearinghouse Rule CR 26-016, SPS 316 adopting the 2023 NEC
Where this is done
EV Charger Installation across Rock County. Each town page has its own local rules and numbers; the rest are on the service area page.
Common questions
EV Charger Installation: questions
How much does it cost to install an EV charger in Janesville?
Wisconsin guides put a Level 2 install at about $800 to $2,900, depending on the run from the panel and whether the charger is included. A panel upgrade, if needed, is extra. See the cost page.
Do I need a permit for an EV charger in Janesville?
Janesville requires a permit for new wiring, and an EV charger is a new 240-volt branch circuit, so the job is permitted and inspected.
Can I plug an EV into a regular outlet?
A standard 120-volt outlet charges slowly (Level 1). A Level 2 charger needs a dedicated 240-volt circuit sized to the charger.
Will I need a bigger panel for an EV charger?
Sometimes. A 200-amp service usually has room; an older 100-amp service may need a load-management device or an upgrade. The electrician's load calculation decides.
Other services
EV Charger Installation in Rock County
Tell us the address and the job. A licensed electrician replies with a price, and nothing starts until you agree to it.
