Skip to content
Call or text (608) 554-4028
Row of breakers in a residential panel with one handle in the tripped middle position

Electrical Repairs, Outlets and Lighting in Janesville

Updated

Get a free quote

A licensed electrician replies with a price. Nothing is booked until you say yes.

Rather talk? Call (608) 554-4028 or text us.

Short answer

Ready for a price on electrical repairs, outlets and lighting?

Call, text, or send the form. You get a written price back before anything is scheduled.

The everyday jobs

Most calls are small: a breaker that keeps tripping, an outlet or a run of outlets that went dead, a GFCI that will not reset, a light that flickers, a new outlet where the furniture ended up, a ceiling fan in place of a light, a row of recessed lights in a kitchen, a hot tub disconnect, or a whole-house surge protector next to the panel.

What they cost

PermitDeck's Milwaukee table puts labor at $65 to $135 an hour with a $144 to $244 minimum call, a new outlet at $176 to $297, and a ceiling fan replacement at $234 to $396 (PermitDeck). A Milwaukee-area contractor lists a diagnostic visit at $150 to $500, a fan on an existing box at $150 to $400 and a whole-house electrical safety inspection at $150 to $350 (its 2026 price guide). Many small jobs get bundled into one visit. All ranges are on the cost page.

Which small jobs need a permit

Janesville does not require a permit to replace an existing switch or outlet in the same location; it does for new wiring or any change to existing wiring (City of Janesville). Milton's code similarly lets broken or defective sockets, switches and receptacles be repaired or replaced without a permit (Milton code 10-212). When a permit applies, Janesville charges $1.17 per outlet, switch or fixture. More in what a homeowner may do alone and Janesville electrical permits.

When a breaker keeps tripping

A breaker trips to protect the wire behind it: from too much load on the circuit, a short, or a ground fault. Resetting it once is fine; one that trips again is telling you something. In a house built from 1965 to the mid 1970s, warm cover plates or a burning smell with it are the warning signs the CPSC lists for failing aluminum connections (aluminum wiring). In a pre-1940 house it can point to old knob-and-tube circuits carrying modern loads.

Hot tubs and outdoor work

A hot tub needs its own 240-volt circuit and a disconnect within sight of the tub. Beloit lists in-ground pools, hot tubs and spas at $35 on its electrical fee schedule (Beloit 2026 fee schedule); in Janesville the work falls under the new-wiring permit. A big new load like a tub or an EV charger is also the moment to check the panel has room (panel upgrades).

Where this is done

Electrical Repairs, Outlets and Lighting across Rock County. Each town page has its own local rules and numbers; the rest are on the service area page.

Common questions

Electrical Repairs, Outlets and Lighting: questions

How much does an electrician charge per hour in Wisconsin?

PermitDeck's Milwaukee table says $65 to $135 an hour for troubleshooting and small repairs, with a $144 to $244 minimum service call. See the cost page.

Do I need a permit to replace an outlet in Janesville?

Not to replace an existing switch or outlet in the same location. Adding an outlet, a circuit or any new wiring needs a permit.

Why does my breaker keep tripping?

Too much load on the circuit, a short, or a ground fault. Reset it once; if it trips again, have the circuit checked rather than resetting it repeatedly.

Do electricians give free estimates?

Many quote larger jobs like panels, EV chargers and rewires for free after a look; diagnostic visits for a problem are usually charged. Ask when you book.

Electrical Repairs, Outlets and Lighting in Rock County

Tell us the address and the job. A licensed electrician replies with a price, and nothing starts until you agree to it.